
Most igniter swaps fail to fix the furnace for one of three reasons: the igniter was never the problem, the replacement doesn’t match what the control board expects, or whatever killed the first igniter is still there. This guide is about avoiding all three, so the new part is the last one you buy for years.
Prove it’s the igniter before you buy one
On a typical induction-draft furnace the board runs a fixed sequence: the thermostat calls for heat, the inducer fan starts, the pressure switch closes to prove draft, the igniter warms up (commonly 15 to 45 seconds depending on the board), the gas valve opens, and the flame sensor must confirm flame within a few seconds. Where the sequence stops tells you which part to suspect.
The most common misdiagnosis is the second row. Because the board only powers the igniter after the pressure switch closes, a failed or blocked pressure switch looks identical to a dead igniter. Read the blink code on the board’s LED through the door window before you order anything. A pressure switch fault code means a new igniter changes nothing.
The cleanest test is voltage, not resistance. With power on, the thermostat calling, and the igniter unplugged from its harness, put a meter on the harness side of the connector during the warm-up window. A 120 V igniter circuit should show roughly line voltage. Voltage present and a dead igniter means the igniter is bad. No voltage means the problem is upstream: pressure switch, limit, board. Some boards ramp the voltage up gradually, so read near the end of the warm-up period.
Resistance checks are weaker than people think. A hairline crack can conduct fine when the igniter is cold and open up as the ceramic expands with heat, so a normal cold reading does not clear it. A visible crack, a chip near the hot zone, or an open circuit does condemn it. Silicon carbide igniters also drift upward in resistance as they age, which means less current, a lower element temperature, and slower ignition well before total failure.
Two materials dominate, and they behave differently enough that swapping one for the other is not always harmless.
The reason this matters: the board is written around one igniter’s heat-up curve and current draw. Universal replacements work in many furnaces, but where the board ramps power, or where a different element runs hotter or slower than the original, you get weak ignition or an igniter that cooks itself early. When possible, match the original part number from the furnace data plate and the existing igniter, then match voltage, connector style, bracket pattern, and element length. Never assume a plug that fits is a part that’s correct.
If the old igniter lasted many years, age was the cause and you can move on. If it died in under two or three years, something is shortening the life of every igniter this furnace gets. The usual causes, in the order worth checking:
Turn off furnace power at the switch and the breaker. Close the gas shutoff so the handle sits crosswise to the pipe. Let everything cool, since a hot igniter assembly and a hot burner box both cause burns.
While the compartment is open, clean the flame sensor with a fine abrasive pad (not coarse sandpaper, which leaves grit and can scratch the rod), check the burner ports for lint and rust, and vacuum out debris. If the igniter died of old age, the sensor is probably the same age and close to its own failure.
Restore gas and power, close the panels so the door switch engages, and run the furnace through at least three full cycles while watching through the sight glass. The igniter should go from dull orange to bright orange or yellow-white, and the burners should light within a few seconds of the gas valve opening. A soft whump or delayed ignition means gas is collecting before it lights, which points to element position, a weak igniter, or dirty burners. Check that your carbon monoxide detectors are working, and smell around any fitting you disturbed.
If you have a meter with a microamp DC range, measure flame sensor current in series with the sensor lead. Boards generally need somewhere around 1 microamp or more to hold the flame, and a healthy sensor often reads a few microamps. A marginal sensor can pass on a clean furnace and then start tripping a few weeks later, and that looks exactly like the new igniter being bad.
After repeated failed ignition attempts most boards lock out, often for about an hour. Cycling power at the furnace switch resets it. If it locks out again immediately, stop and diagnose instead of resetting repeatedly.
If you’re in the Philadelphia area and require furnace replacement servicesCool Aid Co. can find out what it is.
Rough U.S. figures: aftermarket igniters tend to run about $15 to $50, OEM parts about $40 to $150, and a service call with the part commonly lands between $150 and $400. Pricing varies by region and brand. Also check whether the furnace is still under manufacturer parts warranty, because many cover the igniter for the first several years and the serial number on the data plate tells you the install date.